| Author |
 Topic  |
|
| |
Current Topic Rating:  | Join the Forum to Rate this Topic at: www.VNCommodore.com Support Forums
|
|
|
suswpn
P Plater
21 Posts
 |
 Posted - 03 Jun 2012 : 12:47:21 PM
|
just recently replaced the engine, car tries to start but wont fire
its getting fuel to the rail but no fuel into the cylinders has spark fuel pump is fine, im stumped :( anyone had this problem before ?
|
|
Report to Moderator |
|
|
VNSVLE
Forum Moderator
1316 Posts
|
Posted - 03 Jun 2012 : 1:38:37 PM
|
Welcome to the club buddy!!
Have you had it running since the new engine has been in?? |
What's the difference between understeer and oversteer?
Understeer is when the driver is scared.
Oversteer is when the passenger is scared. |
Report to Moderator  |
|
|
suswpn
P Plater
21 Posts
|
Posted - 03 Jun 2012 : 1:47:48 PM
|
| nah mate, are you also on squared arches? iv only just dropped the motor in and bolted it up put oils etc in and tried firing it and nothing just trys to start fuel is going through the rail but the injectors arnt pulsing so fuel is getting into the cylinders. |
| Report to Moderator |
|
|
VNGRPA
Fully Licenced
426 Posts
|
Posted - 03 Jun 2012 : 1:49:22 PM
|
| sounds like a CAS problem if your getting fuel and its just not kicking over, VNSVLE knows heaps about these motors mate so your in good hands, |
| Report to Moderator |
|
|
suswpn
P Plater
21 Posts
|
Posted - 03 Jun 2012 : 2:50:45 PM
|
| yeah sweet, i still have my old motor sitting there so i might take the cas off and put it on this one and see if that fixes the problem |
| Report to Moderator |
|
|
VNGRPA
Fully Licenced
426 Posts
|
Posted - 03 Jun 2012 : 2:53:07 PM
|
| try doing a code check first mate it might save you a bit of time |
| Report to Moderator |
|
|
suswpn
P Plater
21 Posts
|
|
|
VNGRPA
Fully Licenced
426 Posts
|
|
|
VNGRPA
Fully Licenced
426 Posts
|
|
|
VNSVLE
Forum Moderator
1316 Posts
|
Posted - 03 Jun 2012 : 8:37:30 PM
|
Yep over at Squaredarches as well buddy.
Crank angle sensor should throw a code which means your engine check light will be on.
Code 41 I think.
Check your EFI relay and injector wiring just to make sure there is not something you forgot to connect.
Cheers |
What's the difference between understeer and oversteer?
Understeer is when the driver is scared.
Oversteer is when the passenger is scared. |
| Report to Moderator |
|
|
suswpn
P Plater
21 Posts
|
Posted - 03 Jun 2012 : 10:19:20 PM
|
got it working, i got a mate to plug the wiring loom into the computer and one of the little white plugs got hidden behind abit of plastic i got under and sussed out the loom and noticed a plug was missing, fired up thanks christ! haha thanks for the help.
also since i have a 5 litre throttle body, my engine light is always on ? |
| Report to Moderator |
|
|
VNGRPA
Fully Licenced
426 Posts
|
Posted - 03 Jun 2012 : 10:22:37 PM
|
| that would just be the tps on it mate just change it over with a v6 one and the light will go off, glade you got it all sorted |
| Report to Moderator |
|
|
suswpn
P Plater
21 Posts
|
Posted - 03 Jun 2012 : 10:38:55 PM
|
| sweet, il do that tomorow. now i gotta put the tail shaft in and finish the car so i can drive it again ! |
| Report to Moderator |
|
|
VNSVLE
Forum Moderator
1316 Posts
|
Posted - 04 Jun 2012 : 02:15:38 AM
|
| Excellent news buddy!! |
What's the difference between understeer and oversteer?
Understeer is when the driver is scared.
Oversteer is when the passenger is scared. |
| Report to Moderator |
|
|
suswpn
P Plater
21 Posts
|
Posted - 07 Jun 2012 : 10:23:58 AM
|
| so now the car is starting, as soon as you give the car a little throttle it sorta missfires and trys to die :( |
| Report to Moderator |
|
| |
Topic |
|
vn v6 S2 wont start :(
