| Author |
 Topic  |
|
| |
Current Topic Rating:  | Join the Forum to Rate this Topic at: www.VNCommodore.com Support Forums
|
|
|
skotty
P Plater
18 Posts
 |
 Posted - 12 Jul 2008 : 12:33:51 AM
|
Okay so it appears I asked a question and got a thread locked :s wtf...
Does anyone have any idea what else can be causing a '88 VN to stall, its not fuel, its something to do with idled, could it possible be a ECU or a ISC fault? or prehaps the new TPS has gone faulty alltho it never seemed to rev @ 800rpm even after the tps was replaced, it will also stall as soon as you start braking from 60kph...
thanks(lets see luck this time eh?)
|
|
Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 12 Jul 2008 : 09:51:34 AM
|
I locked the thread cause it was a old topic .... thats wft! If your stalling like that did u reset the ecm when you installed the tps? Some error codes would be good, but there is a lot of things that come to mind.. IE crank angle sensor, vacum, dfi modual and there are more that I cant think of right now.... I guess Im saying alittle more info would be good m8 ...(lets see luck this time eh?)  |
3 can keep a secret if 2 are dead |
Report to Moderator  |
|
|
skotty
P Plater
18 Posts
|
Posted - 12 Jul 2008 : 12:06:33 PM
|
How do I do a fault code check on a VN?
If this helps too, the car is a pig to start on cold mornings and puts up a struggle at the best of times? |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
|
|
skotty
P Plater
18 Posts
|
Posted - 12 Jul 2008 : 4:49:14 PM
|
| So it will read out a fault code eventho the light wont come on while driving yeh? |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
|
|
skotty
P Plater
18 Posts
|
Posted - 16 Jul 2008 : 5:15:23 PM
|
I done a fault code check, it is reading 12 so trying to say its fine...
anything else i should look for?
Oh yes, the 2x hoses form the throttle body to the anti polution canister were not on the throttle body aswell... so i re-connected them and it still not idling correctly... |
Edited by - skotty on 16 Jul 2008 5:18:06 PM |
| Report to Moderator |
|
|
skotty
P Plater
18 Posts
|
Posted - 16 Jul 2008 : 5:31:03 PM
|
| I just tried to d/c some sensors and do a fault code test (I dc'd the TPS) and it wouldn't read a fault to that :S.. |
| Report to Moderator |
|
|
V8VNCalais
Fully Licenced
238 Posts
|
Posted - 16 Jul 2008 : 6:49:36 PM
|
| did you go for a drive with the tps disconected?....Is the car stalling when you get off the gas or is it whe you stand o the brake |
| Report to Moderator |
|
|
skotty
P Plater
18 Posts
|
Posted - 16 Jul 2008 : 7:08:55 PM
|
| one i dc'd the tps, the car wouldn't even start and idle... and my gf says it stalls if you brake light but if you brake hard it wont stall :S... |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
|
|
mekkanic
Starting in the driveway
2 Posts
|
Posted - 06 Sep 2008 : 10:47:05 AM
|
| hi there, new member. v.n series 1.back firing, then stalling??? allready reset comp. could the coil pack be breaking down??? |
mekkanic12 |
| Report to Moderator |
|
| |
Topic |
|
Topic Locked
